AndreBenson
Lets talk rear diff lock
As some of you alreadyknow, I have a 1997 Gen 2 Paji.

I have heard that the Gen 2.5 came out with a rear diff lock. Is this correct??

If it is correct. Is there a way of implementing the later into my Gen 2 ?

If there is a way, how would it be engaged?
Blister
Re: Lets talk rear diff lock
AndreBenson wrote:As some of you alreadyknow, I have a 1997 Gen 2 Paji.

I have heard that the Gen 2.5 came out with a rear diff lock. Is this correct??

If it is correct. Is there a way of implementing the later into my Gen 2 ?

If there is a way, how would it be engaged?
Hi Andre!

I have a Gen 2.5 and mine does have a rear diff lock which is engaged with a "moffie" switch (I found that description somewhere on this site)

As to fitting it to your Gen 2, I leave to the experts to comment

Regards

Aslam
AndreBenson
Re: Lets talk rear diff lock
Thanx Aslam

I'll take the moffie knoppie any day.

I can get hold of a rear diff and other interesting parts from the chassis if I need any. So any help regarding this would be much appreciated.

Cherio
Re: Lets talk rear diff lock
Yes, you can retrofit. As far as I know, your 1997 model has all the wiring to allow a plug & play installation if you get the rear axle off a Blister Fender with diff lock as well as the little diff lock air compressor, which lives in the little compartment under the right hand rear seat, and of course the diff lock switch that goes on the center console of the dashboard.

Just be sure to get an axle with the correct final drive ratio or you will have to swop the ring and pinion, which becomes a bit more of a mission.

The Pajero's diff lock is actuated by air pressure, generated by the little compressor.
Gerrit Loubser Image

2003 Toyota Land Cruiser 100 VX TD

2003 Mitsubishi Pajero 3.2 DiD LWB A/T Gone & missed :-(

1999 Nissan Patrol 4.5E GRX M/T: Gone & missed :-(

1996 Toyota Land Cruiser 80 VX 4.5 EFI A/T: SOLD
AndreBenson
Re: Lets talk rear diff lock
Hi Gerrit

That is wonderful news.

So what would I need from this oak.

Compressor
Rear axle with diff lock
Switch
Wiring
Some or other sensor??
And I can probably fit the button anywhere.

thanx again
Re: Lets talk rear diff lock
AndreBenson wrote:I'll take the moffie knoppie any day.
I suspect the "moffieknoppie" concept was invented by owners of so-called serious 4x4s, with solid axles, but no axle diff locks, to explain away the fact that a 4x4 with independent front suspension managed to go up an incline with axle twisters where they could not...
Gerrit Loubser Image

2003 Toyota Land Cruiser 100 VX TD

2003 Mitsubishi Pajero 3.2 DiD LWB A/T Gone & missed :-(

1999 Nissan Patrol 4.5E GRX M/T: Gone & missed :-(

1996 Toyota Land Cruiser 80 VX 4.5 EFI A/T: SOLD
AndreBenson
Re: Lets talk rear diff lock
I'll take the knoppie over a burned clutch any day!!!
Re: Lets talk rear diff lock
AndreBenson wrote:So what would I need from this oak.

Compressor
Rear axle with diff lock
Switch
Wiring
Some or other sensor??
Your list is correct, except that I think you will find all the wiring already in place in your vehicle. Just pay careful attention to where everything was plugged in on the donor vehicle.

I think you will even find that the little orange rear diff lock indicator on the dash will work when you have retrofitted the diff lock.
Gerrit Loubser Image

2003 Toyota Land Cruiser 100 VX TD

2003 Mitsubishi Pajero 3.2 DiD LWB A/T Gone & missed :-(

1999 Nissan Patrol 4.5E GRX M/T: Gone & missed :-(

1996 Toyota Land Cruiser 80 VX 4.5 EFI A/T: SOLD
AndreBenson
Re: Lets talk rear diff lock
Does R12000 for the rear axle and compressor sound expensive??

What can i get for the axle that I am removing??
Re: Lets talk rear diff lock
You could fit a new front difflock for less than that. Simon did some research on it. At the local breaker they want R5k for the rear axle so I reckon R12k is a bit much
Johann Bredell
Post Reply