One of my pet hates is the fugly bumpers seen on so many 4x4s.
The designer puts a lot of hard work into the design and the bumper is then...

Hi Guys, needing some valued advise. I've installed a negative (manual Switch) cut to everything, including chassis earth and battery earth on my Paj...

Well it's me and Mitsu again. I do not want ot bad mouth Mitsu but surely something must be done about their spare part listings and prices.
My short...

I'm looking at putting up a snorkel onto my Paj, are there more positves than negatives in doing this or should I rather stay original and keep...

Thanks to Anton my Bullbar Is now fitted with new spotlights. Stll need to do wiring for spots. IMG_5277.JPG

The idea is for everyone to chip in and contribute. A sort of an Opensource design. Even if you just end up using the dimensions.

Attached is a...

Let me start off by saying, what an usefull forum. I'm a new Pajero owner, One with allot of faults. I bought a lemon on purpose, cheap and with the...

I bought 2 sets of spotlights at Midas this week on special for R499 per set normally R799 a set. Model F500 and on special till this Friday.
I opted...

Since I got my Pajero I was slightly dissapointed in the somewhat 'sissyboy' horn with which it was endowed. For a big vehicle like the Pajero one...

As discussed before I decided to take on the removal of the heads myself.
Not being a mechanic progress is slow but I am at least progressing.
So far...

I have just completed my drawer and fridge slide system for the SWB.
Decided to use 18mm Marine Ply for carcass. This was covered with good quality...

Hi guys

I've been looking at putting air lifters/helpers on my 1997 gen2 Pajero 3.5 LWB as the PJ's rear end started sagging (PJ is even heavier on...

Hiya

I retrofitted keyless entry to my Gen3 a week ago. I have a 2001 DiD and it was annoying missing keyless entry. What a pain not having that....

I'm looking at doing a diy awning, preferably one which does not require supporting poles from the ground (although this is not my main criterion)...

This is a repost of a project I did in early 2008

The original intention was to create a packing system that would add a second floor to the back of...

After seeing this thread

I want to clean my intake system (260'000km demands it I suppose) but also prevent future buildup. My EGR is already...

Hi,
I am looking to fitting a dual battery system in my SWB mainly for a fridge.
I see there is a system from Echo 4X4 (R3200) that charges through...

Hi,

Recently collected my '05 DiD SWB Pajero.

I would like to install a permanent connection for my Nuvi 760 (I hate having cables flopping around...

I bought a pajero for cheap

My New Pajero

Then figured its got a rod knock. More than likely a gudgeon pin

Rod knock causes

So the tear down...

Hi All,

I am just letting you all know that I have started a transplant that I think will really make my Gen 1 SWB a menance to be dealt with....

I decided to change my shocks this weekend. Bar the need for a spanner because of space issues, the entire job can be completed if you own a socket...

When we lived in Australia.. I remember seeing a lot of minis and Land Rovers with white tops... Last week at our local pub, the Platte Bar, I saw a...

Another project I cajoled my friend Brian into doing...
The mounts are designed by HiLift for mounting their jacks to any available part of a...

This was another project I did on my 1988 SWB.. One benefit I found immediately, was that 23 years of accumulated stench disappeared instantly... and...

Last Winter, in the deserts of Arizona, my friend Brian decided to help me make headlight covers for my 1988 SWB... of course he has the tools and a...